Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Like yourself, I get great satisfaction from working with this small kit. Similar to your wine box, I’ve got this old ‘sausage box’ that I can fit everything in, if I’m out the job site or such. It’s a lovely feeling to know that with just this small box of tools, I can pay all my bills and eat. I just wish I could get the rest of my life so minimal!
Super Chunky X Table Plans and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid MegaMax, Diablo blades, Bosch drill bits and Makita … [Read more...]
To see if ShippingPass is right for you, try a 30-day free trial. Also, with ShippingPass, there is no need to worry about commitment. If you decide you want to discontinue the service, you can cancel your subscription at any time. No matter what your shipping needs, Walmart's got you covered. Sign up for ShippingPass so you can shop more, save money and live better.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Work with attention and don’t forget that a good planning will save you from many issues and it will keep the costs within your budget. Invest in high quality materials, such as pine, redwood or cedar. Drill pocket holes before inserting the galvanized screws, to prevent the wood from splitting. Add waterproof glue to the joints, in order to enhance the rigidity of the structure.


A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.

Of course, these wood joints would be almost useless without some sort of adhesive to go with them. Chapter 9 walks you through the most common types of adhesives available for woodworkers and shows you the best one for each job. In Chapter 11, I go over the ins and outs of screws and nails and show you when and where to use them to improve the strength of your joints.
John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
I agree, that’s a nice and easy set up to start with. I’d say a block plane it’s handy for small areas, and touch ups. A no.5 is excellent but a bit heavy and tiring sometimes. I find that a nice rabbet block plane (shoulder + block) with two irons with different sharpening angles it’s essential to me. One fine flat rasp and a medium flat file would complete my set.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
The key to making furniture is having a plan. (Or is that the key to life? I always forget.) The good news for beginning woodworkers is that you don’t need to develop the plan; you need only to follow it. Project plans are abundant and easily found (check out Chapter 21 for some project-plan resources). After you get familiar with the way plans are written, you can build just about anything (depending on your skills, of course).
For very many years (since the early 70’s) I built furniture, that I still have and use, with a Stanley No4 as my one and only plane – and only one blade for it. I still have, and use, that same plane. I now have other planes, but the first one is still my ‘go to’ plane. I have just given away my set of chisels, to my son, as I have collected a few old wooden handled ones which I now prefer, but those old blue plastic Marples set did me well for about 25 years.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
×