As much as I’d like to provide a book with everything you’ll ever need to know about woodworking (as if I even know all that!), it’s just not possible. Chapter 21 is my way of helping you to keep exploring this immense craft by providing you with a bunch of resources. This chapter contains contact info for woodworking magazines, addresses for helpful Web sites, and ideas to help you keep expanding your knowledge and skills.
The first step in developing woodworking skills is to be able to discern the best glues, joints (ways of connecting two pieces of wood), and fasteners to use. Whether you need a dovetail joint for a drawer front or a mortise-and-tenon joint for a table leg, Chapter 10 introduces you to the wonderful world of wood joints. With an understanding of the joints in Chapter 10, you can build any furniture project and make it strong and durable.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
This Welcome Farmhouse Sign post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. Farmhouse style wood signs are a fun way to personalize your space. They are fairly easy to make yourself … [Read more...]
After you have smoothed the wood, you can then decide whether you want to add any color and, if so, what type. You can choose from stain or paint and from water-based, oil-based, or lacquer-based products. You have many options and I’m sure you can find one that works for you. Chapter 17 helps you make sense out of all the choices and shows you how to apply these products.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
If we are out of stock on something you have ordered, we ask you to be patient. We won't forget you or your order, and will ship the missing item within 24 hours after we get it in our warehouse (the expected date on your order is based on the information available at order time). You can cancel a backorder at any time by notifying us by phone, mail, fax or e-mail.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.