Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
The block height’s going to be a personal thing, depending on what you use it for. Mine’s about knee height, which is on the low end, but I did use to do a tremendous amount of prepping straight from the tree. As you’re the same height as me, I’d say 33″ would be a tad on the high side. If you imagine you’ve got a longish piece of wood to work down the length, you want to be holding it almost vertical, rather than angled as it’s less likely to slip. The higher the working surface, the more angled it’s naturally going to become, hence why mine’s so low.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
To see if ShippingPass is right for you, try a 30-day free trial. Also, with ShippingPass, there is no need to worry about commitment. If you decide you want to discontinue the service, you can cancel your subscription at any time. No matter what your shipping needs, Walmart's got you covered. Sign up for ShippingPass so you can shop more, save money and live better.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
A Jack Handplane is a middle size “bench plane” (i.e. planes that are used so often that they are usually on your workbench). If you’re on a budget a jack plane can temporarily be used in place of other planes that perform specialized functions: (1) rough stock removal (if you buy a second iron/blade and shape it with a curved “camber”), (2) jointing board edges (as long as they aren’t too long), and (3) smoothing the boards.
Someone on here made the point that it took them a few years before they got a clear idea about what they wanted to make. I can relate to that. I’m starting to think that I’d like to do a cabinet type build so maybe a plough plane would help with that. There are plenty of old Stanley’s knocking around on Ebay. On the other hand, I’m in no hurry to buy anything else – I feel much more inclined now to make do and explore the limitations of tools that I’ve got.
Of course, these wood joints would be almost useless without some sort of adhesive to go with them. Chapter 9 walks you through the most common types of adhesives available for woodworkers and shows you the best one for each job. In Chapter 11, I go over the ins and outs of screws and nails and show you when and where to use them to improve the strength of your joints.
I sincerely hope this list is helpful to you! Learning to build – to create from scratch things of beauty and function – has been one of the most personally satisfying and empowering experiences I have ever had. I love to see people take up tools and find their creative voice. Wherever you are at in your journey, from learning to read a tape measure to hand tooling furniture in your sleep, we are all in this together. So jump in, get your hands dirty, and let’s build something!
Woodworking For Dummies shows you how your raw building materials stack up, with everything you wood need to know about hardwood, softwood, plywood, veneer wood, plain-sawn wood, rift-cut wood, quarter-sawn wood, solid wood, man-made wood, and more. This down-to-earth guide gives you the goods on how boards are made from trees and the characteristics of hardwood and softwood species, plus all the buzz on
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Like yourself, I get great satisfaction from working with this small kit. Similar to your wine box, I’ve got this old ‘sausage box’ that I can fit everything in, if I’m out the job site or such. It’s a lovely feeling to know that with just this small box of tools, I can pay all my bills and eat. I just wish I could get the rest of my life so minimal!