Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Easy projects show how to get started with an increasingly popular hobby More than 18 million Americans have discovered how satisfying it is to build their own furniture. Packed with detailed illustrations and photographs, this book offers an easy-to-understand introduction to all aspects of woodworking-selecting hand and power tools, setting up a workspace, working with various types of wood, creating edges, joins, applying finishes, and more. Best of all, it includes lots of step-by-step woodworking projects-for dressers, book cases, tables, cabinets, and more-to help people dive right in and start playing in the sawdust. Jeff Strong (Lamy, NM) is a veteran For Dummies author as well as an accomplished wood-worker and furniture-maker who recently completed designs for a commercial line of furniture.
For very many years (since the early 70’s) I built furniture, that I still have and use, with a Stanley No4 as my one and only plane – and only one blade for it. I still have, and use, that same plane. I now have other planes, but the first one is still my ‘go to’ plane. I have just given away my set of chisels, to my son, as I have collected a few old wooden handled ones which I now prefer, but those old blue plastic Marples set did me well for about 25 years.
The block height’s going to be a personal thing, depending on what you use it for. Mine’s about knee height, which is on the low end, but I did use to do a tremendous amount of prepping straight from the tree. As you’re the same height as me, I’d say 33″ would be a tad on the high side. If you imagine you’ve got a longish piece of wood to work down the length, you want to be holding it almost vertical, rather than angled as it’s less likely to slip. The higher the working surface, the more angled it’s naturally going to become, hence why mine’s so low.
Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
now I finally know what to recommend my friends when I try to convince them to give handtools a try (I currently am doing an apprenticeship in cabinetmaking (unfortunately mostly particle board) and said friends they do the same and often have no clue what can be achieved with handtools alone) because up until now, I never knew what to recommend for sharpening as my setup is great but very expensive. And I guess if I recommend to get two stones instead of a combination stone, one can keep one side flat for flattening the backs of new chisels, and add a strop with some polishing compound I really can’t think of anything else one would need for a long time!
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
I have so many free woodworking plans on the site, that it is so hard for a beginner to choose something both simple to build and fulfilling. That is why, I decided to make a short list with my top 20 favorite projects that can be built by any person with basic woodworking skills and limited tools. Even if it might look intimidating at first, my detailed plans and step by step instructions make it really easy for anyone to get the job done.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!