By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Gord, 1/2/2013 Nice inexpensive starter set I purchased for my Little Brother. The planes were easy to disassemble for sharpening and the blades sharpened easily. The blades were ground a bit low in the center but was easily corrected with a course stone. There was a problem with the wooden box and after a few iffy phone calls a replacement box was received well before Christmas.
I quickly found that power equipment was not broadening my capabilities as much as it was like an anchor tethering me to a limited band of work and taking up valuable shop space. I also didn’t like wearing the requisite dust mask, hearing protection and safety glasses all the time – it was like a mini sensory deprivation chamber. When I asked master cabinetmaker Dan Faia what he does for dust protection in his own shop, his succinct reply was “I never coughed up a curl.” That pithy remark reflected the very different view traditional woodworkers have – without all the big machines, the dust and noise, you can focus on the work, invest in a smaller set of high quality tools that should last a lifetime and enjoy the process as much as the result.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
John, 9/18/2012 Arrived quickly and in a real beautiful box. I sharpened and honed the planes and used them to smooth some old cedar boards. They worked flawlessly even for this beginning woodworker. A real joy using these types of tools instead of power sanding tools and the like. I have never used a Spokeshave before but can already see that it will be very useful as I progress in my journey from welder to woodworking.

excellent post! noone can beat good advice from someone who makes a living at this. it’s struggle to commit to minimal tools but i can attest to getting too many too soon and not mastering them all. it can even slow down a project trying to fiddle with a new tool and create some waste. i’ve taken to the idea to make 6 projects with the same problem i like to solve with a specialty tool. then ask do i really need it.. for instance i want to incorporate more sliding dovetails. as per you sound advice you don’t need anything more than what you listed but i keep eyeing a dovetail planes both male and female. i just saying resist and build! learn efficiency with what i have and decide if its a roadblock to success or profitability
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ...  More + Product Details Close
×