I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
The block height’s going to be a personal thing, depending on what you use it for. Mine’s about knee height, which is on the low end, but I did use to do a tremendous amount of prepping straight from the tree. As you’re the same height as me, I’d say 33″ would be a tad on the high side. If you imagine you’ve got a longish piece of wood to work down the length, you want to be holding it almost vertical, rather than angled as it’s less likely to slip. The higher the working surface, the more angled it’s naturally going to become, hence why mine’s so low.
Below you will find some of the free woodworking plans to be found on the net. Much of the information was gathered from the newsgroup rec.woodworking (also available via google groups). This list is far from complete. I'd suggest you learn to use a search engine like Altavista or Google. Just type in the project name you want to do, and "plans". This will help you find all sorts of things.
24″ for the chopping block. all of my lumber comes from last years spring clean up. currently have Cherry, White oak, Ash, Hard & Soft Maple as Well as Sasafrass on hand there is also Birch in the woods but none of them have needed to come down yet. I keep two single bevel axes one light one Heavy(2-1/2 lb) which I use depends on how my Elbow feels. A Froe is also required. I think going from tree to board is harder than from board to furniture but it depends how much wind is in the tree. I don’t think I would of ever been able to build the required skills if I had to pay for the lumber though I guess I paid in labor. Air dried stuff is some much better to work with its worth it.
Own one junk chisel, probably about 1″. This will keep you from doing what you oughtn’t to your good chisels. It can be used and can be nearly trash. It’s going to hit caulk on masonry, junk stuck to the floor, interior cuts on thin sheets of aluminum, and other such abuse. If the back and bevel sort of intersect on an extra coarse stone, it’s sharp. I’ve sharpened mine on the concrete back stoop. (Not so great for the concrete)
Just for the record, a jointer and planer are not from the ICDT kit – the philosophy on that column is, indeed, beginner AND basic (hence the Workmate). The tools we suggest in the ICDT manual are for those who are working at a kitchen table or in a backyard; the tools the editors would recommend for someone who is quite sure he or she wants to pursue serious furniture making would be rather different.
After the wood is cut it needs to dry before it can be used, and drying the wood causes shrinkage in the board. So it’s important that the board be allowed to dry evenly or it twists, bows, or warps. If you buy wood from a lumberyard, it’s already been dried, but you want to acclimate it to your shop before you work with it. This way the wood will make any changes it needs to make with the different humidity level in your shop, and you don’t get any nasty surprises like a table leg that twists after you’ve glued your project together.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
As someone who finds hand planing a challenge the minimalist approach seems like the best way to truly learn a tools quirks and develop the skill required. So the Veritas BU planes are going along with the Tormek required to sharpen those gargantuan irons and a diamond plate and oil stone are on the way to get my old Stanley no 5 humming. I never found a sharpening routine that didn’t look a ball ache to keep the BU planes working well and being a stick thin wimp the weight of the buggers for anything more than controlled smoothing shavings knackered me out.
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ... More + Product Details Close