Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.

Backpack storage and organizer Plans and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Milwaukee hammer drill/impact combo, Diablo … [Read more...]


Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
To start off you only need either a 1/4″ or 3/8″ mortise chisel (or some size close to those). You don’t need a whole set of mortise chisels. Mortise chisels (also spelled “mortice”) are used for chopping mortises (rectangular holes) into the side of your board for insertion of a tenon. “Mortise and Tenon” is a very common and very strong joint that most people have heard of.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
×