Like yourself, I get great satisfaction from working with this small kit. Similar to your wine box, I’ve got this old ‘sausage box’ that I can fit everything in, if I’m out the job site or such. It’s a lovely feeling to know that with just this small box of tools, I can pay all my bills and eat. I just wish I could get the rest of my life so minimal!
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Below you will find some of the free woodworking plans to be found on the net. Much of the information was gathered from the newsgroup rec.woodworking (also available via google groups). This list is far from complete. I'd suggest you learn to use a search engine like Altavista or Google. Just type in the project name you want to do, and "plans". This will help you find all sorts of things.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
John, 9/18/2012 Arrived quickly and in a real beautiful box. I sharpened and honed the planes and used them to smooth some old cedar boards. They worked flawlessly even for this beginning woodworker. A real joy using these types of tools instead of power sanding tools and the like. I have never used a Spokeshave before but can already see that it will be very useful as I progress in my journey from welder to woodworking.
After the wood is cut it needs to dry before it can be used, and drying the wood causes shrinkage in the board. So it’s important that the board be allowed to dry evenly or it twists, bows, or warps. If you buy wood from a lumberyard, it’s already been dried, but you want to acclimate it to your shop before you work with it. This way the wood will make any changes it needs to make with the different humidity level in your shop, and you don’t get any nasty surprises like a table leg that twists after you’ve glued your project together.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
Woodworking is a fairly technical subject with its own rules and language. Because of this, I include a lot of terms you may not be familiar with. Rather than include a glossary of terms, I’ve chosen to provide definitions or cross-references for terms that are part of the woodworking vocabulary. These terms are in italics to help you identify them.
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ... More + Product Details Close