I dedicate several chapters in this book to exploring the exciting world of tools. From age-old hand tools to the most modern machine for milling wood, Chapters 5, 6, and 7 cover them all (well, not all of them, that would be insane, not to mention take up the entire book). Not only do you get to see what tools are what, you also get a glimpse into how to use each of them safely and effectively.
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
24″ for the chopping block. all of my lumber comes from last years spring clean up. currently have Cherry, White oak, Ash, Hard & Soft Maple as Well as Sasafrass on hand there is also Birch in the woods but none of them have needed to come down yet. I keep two single bevel axes one light one Heavy(2-1/2 lb) which I use depends on how my Elbow feels. A Froe is also required. I think going from tree to board is harder than from board to furniture but it depends how much wind is in the tree. I don’t think I would of ever been able to build the required skills if I had to pay for the lumber though I guess I paid in labor. Air dried stuff is some much better to work with its worth it.
A woodworking project wouldn’t be complete without the finish. Part V helps you make this often hated (trust me, I’m being nice here) process of sanding and finishing into a chore that you’ll love (okay, maybe just tolerate). Chapter 16 explores the often short-shrifted process of filling and sanding the wood smooth. Chapter 17 shows you how to add color to the wood. Chapter 18 demystifies the topcoat process. In this chapter, you discover the best type of finish for your project and go through the steps of applying it for best results.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
Part III gets into the nuts and bolts of joining wood together (you don’t use actual nuts and bolts, though). Chapter 9 is all about adhesives (glues). This chapter demystifies all the different glue choices you have to contend with. After reading this chapter, you’ll be able to walk into a woodworking store and get the right glue for you. Chapter 10 shows you how to make all the wood joints you’ll encounter in this book. Wood joints are the basis for almost all woodworking, and making them well is the difference between a project that lasts for a few years (at most) and one than is still solid after generations. Chapter 11 offers your wood joints some assistance with mechanical fasteners such as screws and nails. This chapter shows you when adding a nail or screw to your project can help and when it’s a waste of effort.
*Northern Ireland, Scottish Highlands and Islands usually receive a 2-3 working day service for First Class. For Tracked Courier, it’s a 2 working day service and you need to order by 15:00. Unfortunately, we don't currently offer Express Delivery outside the UK, Gibraltar, Guernsey or Jersey. All deliveries are subject to cut-off times and public holidays.
After the wood is cut it needs to dry before it can be used, and drying the wood causes shrinkage in the board. So it’s important that the board be allowed to dry evenly or it twists, bows, or warps. If you buy wood from a lumberyard, it’s already been dried, but you want to acclimate it to your shop before you work with it. This way the wood will make any changes it needs to make with the different humidity level in your shop, and you don’t get any nasty surprises like a table leg that twists after you’ve glued your project together.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Woodworking For Dummies shows you how your raw building materials stack up, with everything you wood need to know about hardwood, softwood, plywood, veneer wood, plain-sawn wood, rift-cut wood, quarter-sawn wood, solid wood, man-made wood, and more. This down-to-earth guide gives you the goods on how boards are made from trees and the characteristics of hardwood and softwood species, plus all the buzz on
If I were to give someone new one piece of advice, it would be to buy their chisels new, not used. I have wasted more time and more money trying to save butchered chisels than I want to admit. There’s a good chance that the used chisel will be bellied in the back or pitted at the edge and it will take more than beginner skills to fix it. You may make things worse rather than better. Sure, learn to do this _some_ day, but maybe not as a beginner first thing. I’ve had similar problems with used planes, but it isn’t nearly as bad a problem for a joinery plane. If there are pits that lead to scratches, it may not matter for anything other than a final smoother. Also, a tiny back bevel may save the day on a plane, but you likely don’t want that on a chisel. So, I’m less fussed about planes and, if it all goes south, you can buy a new blade for smoothing work and use the old for rough work (all in the same plane). You can’t buy a new blade for a chisel. Well, you can, but it’s called buying a new chisel. I use 3/8″ a lot. 1/4, 3/8 to handle all the mortises and dovetails and either 3/4 or 1″ for paring shoulders and for fat parts of some dovetails. I probably learn towards the 1″ because there are times you want to reference off the blade to keep moving in a line, like for a housing. I think Lee Valley’s version of the Narex are excellent and mine came with flat backs that could go straight to polishing.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
Second, my table saw. I would love to have one of the big cabinet table saws that start in the four digit range, but, really, my Dewalt Job Site saw has done a mighty fine job for the three or so years we have owned it. The alignment continues to be right on, even after being toted around, and like every other Dewalt tool I have owned, it is an absolute work horse.
Just bought this book.I want to learn to build things in wood.I have some tools but those joints are giving me problems. I have design books but how do I make a mortise joint or when to use tendon joint or a rabbit or use dowels? Who knew.I got some basic things but now I can actually finish my projects oh Joy.I can't wait till it arrives .Thank you Amazon and Hippo_Books for this book. When I get better at building stuff I will be back to update my review.Oh to all of you reviewers ....I bought this book cause of you.So thank you.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
This is a super cheap option for a pretty diverse tool. Like, how wrong can you go for $34, right? This tool rocks for doing cuts on larger pieces of wood that need to be more detailed than your circular saw will allow. For more detailed work I would totally go for a scroll saw, or even a band saw. But if you are building your tool box, this is a much more approachable item, both price wise and in terms of ability to be used in diverse ways. And, hey, woodworking isn’t exactly inexpensive, right?
I tried to write a book that contains all the essential information for the novice woodworker as well as some more advanced tips and tricks to jumpstart your existing woodworking skills. You won’t find any useless theories or unnecessary technical jargon to bog you down. What you will find is practical, hands-on information and advice that will save you hours of frustration (pretty good deal, huh?).
It is my understanding that frame saws are standard to a continental toolkit. Richard’s list of a hard-point handsaw, 10-12” backsaw, and coping saw is a very standard British/American toolkit, that preforms the same roles as the frame saws you detailed. All three are available in every hardware store in America and I assume in Britain, true hardware store back saws are now junk and to get something new that preforms as well an old Disston, like Richard stated, you have to upgrade to likes of Veritas and Lie-Nielsen.
John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.