John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
The last tool I recommend for every beginning woodworker is a quality router. While many routers available today offer two different bases (a stationary base and a plunge router base), for most beginners, a quality stationary base model will take care of quite a number of tasks, and can also be mounted in a router table should you choose to invest in (or even build one) one down the line. Choose a router model that is at least 2-HP and has electronic variable speed controls (as larger cutting bits should use slower speeds), a soft start mechanism and is easy to make bit changes (preferably with the ability to use both 1/2-inch and 1/4-inch shank router bits).
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
I use chisels perhaps more than any other tool in my workshop, so it’s a good idea to not cheap out here. A high quality set of bevel edge bench chisels (new or vintage) will last you many years (likely your entire life) and will be used on nearly every project. I’ve used some descent affordable plastic handle bench chisels, but highly prefer lighter wooden handle chisels with excellent steel.
This book is organized modularly, which means that you can read it from cover to cover and progressively build your woodworking knowledge. Or you can skip around and choose a subject that interests you from the table of contents or index, and start reading it immediately without feeling lost. Throughout the book I also include cross-references to where you can find more information about a subject.
In this guest perspective from Bill Rainford, traditional joiner, we learn a powerful method for analyzing today’s tool prices and thinking about which tools you really need in your shop. This article is about woodworking hand tools, but as someone who has visited Bill’s shop, I can tell you that he is no hand-tool purist. You’d love some of the machinery, new and old, he has acquired and cared for over the years.
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
No joke. As you get into building you’ll discover that woodworkers use jigs for everything, and that can be intimidating. The Kreg Jig company has absolutely knocked it out of the park in making jigs accessible, easy to use, and so incredibly useful that you’ll wonder why you didn’t think of that. They are affordable, and after just one build you will be singing the holy Kreg praises. I won’t go into each one, though I am happy to answer any questions you may have. Here’s a list of the jigs I have used and found incredibly helpful. (It’s a growing list!)
The number one thing to know is that wood isn’t a static thing. It’s a natural product that’s constantly in movement. As a woodworker, your job is to understand how wood moves and how to use that movement to your best advantage (or at least how to keep it from ruining your masterpiece). This chapter helps you to understand how boards are made out of trees and to discover that the way the log is cut determines its ultimate strength and stability (and its beauty). Additionally, you explore the characteristics of a variety of species of hardwoods and softwoods.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
Last, but not least…but often left until last, let’s talk routers. If you already own Ryobi batteries, this is the no-brainer entry-level router for you. As you get into doing more router work you will learn there are different kinds of routers (trim, combination, and full size). Honestly, I don’t own this router, and when I first purchased a router a number of years ago I had no idea what I was getting. If I did it again I would start here and get comfortable with it, then decide from there what my main applications are. I will add that if you are using a router table, which I totally recommend (I use this one), you will need a full size. My old router is going out right now, and I will likely replace it with this Bosch model.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ... More + Product Details Close