This doesn’t have to be true and you will find that a small set of tools can stretch a very long way and get you building quickly. Moreover it will light your path to future tool acquisitions by showing you clearly where a task could be made easier with a more specialized tool. For instance, a chisel can pretty much do anything in woodworking, but using just a chisel for some thing is just plain awful. But the chisel can do it so on that first project you may spend a bit more time with chisel and saw to cut that rabbet and when the next project comes around you invest in a rabbet plane. Slowly you start to build a comprehensive tool kit as the tools are needed.
It’s okay to buy wood with knots, splits, cracks, and checks. These defects affect only a small area of the board (if they exist over the majority of the board, don’t buy it), so you can plan your cuts around them. Avoid boards with warps, twists, or bows. It takes a lot of time to flatten a board that has one of these defects. To test for these defects, place one end of the board on the floor and hold the other end to your eye. The board should be straight and true. If not, leave it there.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt. Unfortunately, that ended up with the guy we hired stealing from us…..uggggh. When will we ever learn to not be so trusting?! Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!! Sad. Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
I sincerely hope this list is helpful to you! Learning to build – to create from scratch things of beauty and function – has been one of the most personally satisfying and empowering experiences I have ever had. I love to see people take up tools and find their creative voice. Wherever you are at in your journey, from learning to read a tape measure to hand tooling furniture in your sleep, we are all in this together. So jump in, get your hands dirty, and let’s build something!
This snowman kit post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. The snowflakes are falling softly on the ground. You grab your hat, coat and mittens and head outside to test the snow. … [Read more...]
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
Someone on here made the point that it took them a few years before they got a clear idea about what they wanted to make. I can relate to that. I’m starting to think that I’d like to do a cabinet type build so maybe a plough plane would help with that. There are plenty of old Stanley’s knocking around on Ebay. On the other hand, I’m in no hurry to buy anything else – I feel much more inclined now to make do and explore the limitations of tools that I’ve got.
If we are out of stock on something you have ordered, we ask you to be patient. We won't forget you or your order, and will ship the missing item within 24 hours after we get it in our warehouse (the expected date on your order is based on the information available at order time). You can cancel a backorder at any time by notifying us by phone, mail, fax or e-mail.
Convert your Delta Midi-Lathe to a full size Convert your Delta Midi-Lathe to a full size lathe by adding the Delta Midi Lathe Bed Extension. Featuring a modular design so you can connect multiple extensions this extension increases bed length by 25-1/2 in. so you can turn longer spindles. To reduce vibration add 34 lbs. of cast iron ... More + Product Details Close
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.