About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Work with attention and don’t forget that a good planning will save you from many issues and it will keep the costs within your budget. Invest in high quality materials, such as pine, redwood or cedar. Drill pocket holes before inserting the galvanized screws, to prevent the wood from splitting. Add waterproof glue to the joints, in order to enhance the rigidity of the structure.
The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project.
I tried to write a book that contains all the essential information for the novice woodworker as well as some more advanced tips and tricks to jumpstart your existing woodworking skills. You won’t find any useless theories or unnecessary technical jargon to bog you down. What you will find is practical, hands-on information and advice that will save you hours of frustration (pretty good deal, huh?).
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
*Northern Ireland, Scottish Highlands and Islands usually receive a 2-3 working day service for First Class. For Tracked Courier, it’s a 2 working day service and you need to order by 15:00. Unfortunately, we don't currently offer Express Delivery outside the UK, Gibraltar, Guernsey or Jersey. All deliveries are subject to cut-off times and public holidays.
Woodworking is one of those activities that stimulates your creativity and gives you self confidence. As any other hobby, you should start with basic projects so you get accustomed with the skills and then move to more challenging projects. If you have a stressful life or you are just looking for an activity to help you bond with your family or friends, doing DIY projects is the ideal choice.
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ... More + Product Details Close
Woodworking For Dummies shows you how your raw building materials stack up, with everything you wood need to know about hardwood, softwood, plywood, veneer wood, plain-sawn wood, rift-cut wood, quarter-sawn wood, solid wood, man-made wood, and more. This down-to-earth guide gives you the goods on how boards are made from trees and the characteristics of hardwood and softwood species, plus all the buzz on
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
I've only been woodworking for a few months and am still very much a novice. I bought this book hoping to learn some creative, but easy methods or time saving tips, but as my title implys, this book contains only the most basic of techniques. However, this book is very good for understanding basic terminology. This was my first "for dummies" book so maybe I was expecting too much. A few episodes of the New Yankee Workshop and/or a few hours of browsing the internet and you can learn the majority of what this book covers.
Backpack storage and organizer Plans and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Milwaukee hammer drill/impact combo, Diablo … [Read more...]
However, I would recommend that you either build a wooden workbench, or purchase one if you feel a workbench build is too advanced for you right now. However, I created the DVD “Building the Portable Moravian Workbench with Will Myers” so that even beginners can build a solid, portable, and very affordable workbench that will fit almost anywhere, using mostly or only hand tools. You can buy it in my store here. You can find Will’s free workbench plans for the Moravian Workbench here. Whichever path you choose, make sure you choose to either build or buy a heavy & sturdy wooden workbench, with at least a 3″ solid top, strong supportive base legs, and two strong vises.
now I finally know what to recommend my friends when I try to convince them to give handtools a try (I currently am doing an apprenticeship in cabinetmaking (unfortunately mostly particle board) and said friends they do the same and often have no clue what can be achieved with handtools alone) because up until now, I never knew what to recommend for sharpening as my setup is great but very expensive. And I guess if I recommend to get two stones instead of a combination stone, one can keep one side flat for flattening the backs of new chisels, and add a strop with some polishing compound I really can’t think of anything else one would need for a long time!
Part IV is filled with really cool projects. The purpose of this section is to give you some woodworking experience and to progressively build your skills. Chapter 12 leads you through the process of making a project so that you know what you’re getting into before you begin cutting wood. Chapter 13 gets you started woodworking with the easiest project to build — a bookcase. Not just one bookcase, but several, so you’re sure to find one that fits your design ideals. Chapter 14 builds on the skills you developed in Chapter 13 by helping you build tables. Like Chapter 13, you have several table designs to choose from (heck, build ’em all; you can never have too many tables!). Chapter 15 ups the ante by providing projects for making cabinets with either drawers or doors. Again, you get to choose among several really good designs (if I do say so myself).
Basic woodworking tools are different from beginner woodworking tools. For one thing, I don’t like to use the word “beginner” unless I am using it accurately. It’s not a very useful label, in my opinion, because it implies that there are clear-cut and hierarchical steps in your growth as a woodworker. Who wants to return to grade school during his or her valuable shop time? So I only use the word “beginner” when I’m talking about someone who is touching woodworking tools for the first time.
Woodworking is a fairly technical subject with its own rules and language. Because of this, I include a lot of terms you may not be familiar with. Rather than include a glossary of terms, I’ve chosen to provide definitions or cross-references for terms that are part of the woodworking vocabulary. These terms are in italics to help you identify them.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
My Stanley 51/2 was in a bit of a state when I got it and refurbing it took a bit of time and cash. Now it works a treat and looks like new. I’m nearly through the bench build and have spend hours using it – it really is a workhorse piece of kit. I did some final cleaning up of some oak legs the other day and I can’t really see how a smaller plain would do a better job.
Youve seen a few shows on TV, and working with wood looks like it could be quite entertaining and rewarding. After all, you get to create something that you can proudly display to your friends and family. But where and how do you begin to move from expressed interest to hands-on experience? Woodworking For Dummies shows you how your raw building materials stack up, with everything you wood need to know about hardwood, softwood, plywood, veneer wood, plain-sawn wood, rift-cut wood, quarter-sawn wood, solid wood, man-made wood, and more. This down-to-earth guide gives you the goods on how boards are made from trees and the characteristics of hardwood and softwood species, plus all the buzz on Gearing up with the right tools Putting safety first in your workshop Using adhesives and glue Working with wood joints Smoothing it out by sanding and filling Adding color with stains and paints Protecting your work with topcoats Whether you want to put together a simple plywood bookcase or an incredible solid oak dining table, Woodworking For Dummies can help you get organized as you craft your plans for a piece thatll reflect your personal touch. Youll discover how to Measure and mark your wood Distinguish among saw designs Choose and use sharpening tools Hone in on hot melt glue Speed things up with modern frame joints Get down to the nitty-gritty on nails Apply water-based polyurethanes This handy reference packs in essential information for the novice woodworker and some advanced tips and tricks to jumpstart any woodworkers existing skills. Includes detailed illustrations and how-to photos.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.