The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project.

John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.


Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
In 1900, just as it was when I was a student over 100 years later, the view is that it is better to buy a quality tool once that will last a lifetime than buy something of poor quality which will not serve you well in your work. Keep that in mind as you review the list — since the tools were not the cheapest back then and surely are not the cheapest today. But with this modest set of tools you can build an amazing array of projects just as many ‘Sloyders’ (Sloyd school students) have done before us.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
I created these hand tool buyer’s guides to help beginners who feel overwhelmed when trying to understand which hand tools they need first. It’s frustrating! Below you’ll see my summary list of the 20 basic professional woodworking hand tools that you should start to accumulate in order to start building the most basic woodworking projects. When you’re ready, you can follow the yellow buttons to visit each of the buying guides for each type of hand tool, to get help with understanding hand tool features, brands, & models. At the bottom of this page is a handy full list of tools that is sorted by “urgent”, “semi-urgent”, and “not-urgent” to buy.
Backpack storage and organizer Plans and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Milwaukee hammer drill/impact combo, Diablo … [Read more...]

Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.


Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.

I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.

Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
Tools for children must work right out of the box without modification. Only a minimal amount of skill should be necessary to put the tools into service, and they need to fit small hands. The tools contained in the Highland Woodworking Kids' Tool Kit meet these standards, and are suitable for kids 7 years old and up with adult supervision. As for materials, stick with softer woods like white pine and basswood. These woods are inexpensive, easy to work and readily available at any home center.
The first step in developing woodworking skills is to be able to discern the best glues, joints (ways of connecting two pieces of wood), and fasteners to use. Whether you need a dovetail joint for a drawer front or a mortise-and-tenon joint for a table leg, Chapter 10 introduces you to the wonderful world of wood joints. With an understanding of the joints in Chapter 10, you can build any furniture project and make it strong and durable.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
It’s okay to buy wood with knots, splits, cracks, and checks. These defects affect only a small area of the board (if they exist over the majority of the board, don’t buy it), so you can plan your cuts around them. Avoid boards with warps, twists, or bows. It takes a lot of time to flatten a board that has one of these defects. To test for these defects, place one end of the board on the floor and hold the other end to your eye. The board should be straight and true. If not, leave it there.
You’ve seen a few shows on TV and working with wood looks pretty fun. After all, you get to use your hands and create something that you can proudly display to your friends and family. But where do you begin to learn to do woodworking? This part provides you with the basic vocabulary from which to build your woodworking skills. Chapter 1 shows you all the steps involved with making a woodworking project, Chapter 2 introduces you to the various qualities of wood, and Chapter 3 helps you get up to speed with your woodworking space and workshop safety.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.

Oakman, 1/12/2015 If you are planning on remaining a beginner then these are fine but..... The soles of the planes are not flat. Planes will only flatten a surface as flat as their soles and the ones I received are not flat and the work I would need to do in order to flatten the is excessive. The sides of both planes I received are not square. I sharpened the blades after cleaning the shipping oil from them. (they did arrive clean). I did get them adjusted to shave a nice thin strip off the piece I was working on but it was not flat due to the sole issues stated above. Had I performed these tests promptly upon receipt of the planes, I would have returned them. They will serve a purpose but they are not what I expected.
Second, I assumed that you want to do things the fast and easy way and not necessarily the old-fashioned way. As you’ll likely find out by talking to other woodworkers, you can find almost as many ways to perform a task as you can find woodworkers. Everyone has his own unique way to do things and mine involves taking advantage of modern tools and shortcuts, rather than using old-fashioned, time-consuming, and often frustrating approaches that can be done better with modern tools and approaches (do you sense a little bias here?). For example, if you want to find out how to craft dovetails by hand with a chisel and backsaw, buy another book. But if you want to make joints that are just as strong and beautiful in a fraction of the time with a router and a jig, then this book is for you. (Don’t worry, in this book, you will still get to see many of the traditional ways things are done, if for no other reason than to help you decide for yourself how you want to approach a task.)
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
In 1900, just as it was when I was a student over 100 years later, the view is that it is better to buy a quality tool once that will last a lifetime than buy something of poor quality which will not serve you well in your work. Keep that in mind as you review the list — since the tools were not the cheapest back then and surely are not the cheapest today. But with this modest set of tools you can build an amazing array of projects just as many ‘Sloyders’ (Sloyd school students) have done before us.
Dummies has always stood for taking on complex concepts and making them easy to understand. Dummies helps everyone be more knowledgeable and confident in applying what they know. Whether it's to pass that big test, qualify for that big promotion or even master that cooking technique; people who rely on dummies, rely on it to learn the critical skills and relevant information necessary for success.

MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
The number one thing to know is that wood isn’t a static thing. It’s a natural product that’s constantly in movement. As a woodworker, your job is to understand how wood moves and how to use that movement to your best advantage (or at least how to keep it from ruining your masterpiece). This chapter helps you to understand how boards are made out of trees and to discover that the way the log is cut determines its ultimate strength and stability (and its beauty). Additionally, you explore the characteristics of a variety of species of hardwoods and softwoods.
Woodworking For Dummies shows you how your raw buildingmaterials stack up, with everything you wood need to knowabout hardwood, softwood, plywood, veneer wood, plain-sawn wood,rift-cut wood, quarter-sawn wood, solid wood, man-made wood, andmore. This down-to-earth guide gives you the goods on how boardsare made from trees and the characteristics of hardwood andsoftwood species, plus all the buzz on
Two things which I took to instantly and now wouldn’t want to do without are an old-fashioned two foot, four fold ruler which gets used all the time (there’s nothing that comes close to it) and a 1 1/2″ butt chisel which gets used all the time for marking anything which needs to be chopped e.g. the side of a mortice. It also means fewer chops and therefore a bit more accuracy when cutting out a knife wall.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]

This wood bench plan is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. My neighbor saw a cute wood bench at a local restaurant and wanted one for her house.  She snapped a few pics for me, … [Read more...]
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
The very affordable coping saw (often around $20) is regularly used for rough cutting shapes in the board, but especially for removing waste from dovetail joints (one of the most common wood joints). An affordable coping saw will work just fine as long as you have plenty of replacement blades on hand (also very affordable). Read my hand saw buying guide for more detail on brands & features to look for when purchasing a coping saw. 
×