Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.

WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
I've only been woodworking for a few months and am still very much a novice. I bought this book hoping to learn some creative, but easy methods or time saving tips, but as my title implys, this book contains only the most basic of techniques. However, this book is very good for understanding basic terminology. This was my first "for dummies" book so maybe I was expecting too much. A few episodes of the New Yankee Workshop and/or a few hours of browsing the internet and you can learn the majority of what this book covers.
In researching the Sloyd tool cabinet shown at left I found some old tool catalogs from Chandler & Barber of Boston (a primary supplier of Sloyd paraphernalia), including one from 1900 complete with a list of pricing for all the tools in the cabinet. This got me thinking. According to the Federal Reserve’s website, $1 in 1900 should be worth about $27 today. Yet a straight monetary conversion doesn’t paint a complete picture since some tools that were common back then are a specialty today, and vice versa. So I created a spreadsheet that includes columns for the original hand tool prices, those same prices adjusted for inflation and actual prices for similar tools from today’s retailers. Click here to see that spreadsheet.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
I have so many free woodworking plans on the site, that it is so hard for a beginner to choose something both simple to build and fulfilling. That is why, I decided to make a short list with my top 20 favorite projects that can be built by any person with basic woodworking skills and limited tools. Even if it might look intimidating at first, my detailed plans and step by step instructions make it really easy for anyone to get the job done.
Very interesting data! And I have to acknowledge the diminishing return on machine tools and the accretive returns of hand tools. But I do woodworking as a beloved hobby. It is great to spend time creating a classic dovetailed drawer from quartersawn oak using hand tools. But I don’t want to use my limited time preparing rough-milled stock to workable dimensions. So, I’m blessed to have a tablesaw, a jointer, a planer, and a bandsaw as well.

We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
As much as I’d like to provide a book with everything you’ll ever need to know about woodworking (as if I even know all that!), it’s just not possible. Chapter 21 is my way of helping you to keep exploring this immense craft by providing you with a bunch of resources. This chapter contains contact info for woodworking magazines, addresses for helpful Web sites, and ideas to help you keep expanding your knowledge and skills.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project.
I've only been woodworking for a few months and am still very much a novice. I bought this book hoping to learn some creative, but easy methods or time saving tips, but as my title implys, this book contains only the most basic of techniques. However, this book is very good for understanding basic terminology. This was my first "for dummies" book so maybe I was expecting too much. A few episodes of the New Yankee Workshop and/or a few hours of browsing the internet and you can learn the majority of what this book covers.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.

I created these hand tool buyer’s guides to help beginners who feel overwhelmed when trying to understand which hand tools they need first. It’s frustrating! Below you’ll see my summary list of the 20 basic professional woodworking hand tools that you should start to accumulate in order to start building the most basic woodworking projects. When you’re ready, you can follow the yellow buttons to visit each of the buying guides for each type of hand tool, to get help with understanding hand tool features, brands, & models. At the bottom of this page is a handy full list of tools that is sorted by “urgent”, “semi-urgent”, and “not-urgent” to buy.


Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

The last tool I recommend for every beginning woodworker is a quality router. While many routers available today offer two different bases (a stationary base and a plunge router base), for most beginners, a quality stationary base model will take care of quite a number of tasks, and can also be mounted in a router table should you choose to invest in (or even build one) one down the line. Choose a router model that is at least 2-HP and has electronic variable speed controls (as larger cutting bits should use slower speeds), a soft start mechanism and is easy to make bit changes (preferably with the ability to use both 1/2-inch and 1/4-inch shank router bits).
If we are out of stock on something you have ordered, we ask you to be patient. We won't forget you or your order, and will ship the missing item within 24 hours after we get it in our warehouse (the expected date on your order is based on the information available at order time). You can cancel a backorder at any time by notifying us by phone, mail, fax or e-mail.
The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
The last tool I recommend for every beginning woodworker is a quality router. While many routers available today offer two different bases (a stationary base and a plunge router base), for most beginners, a quality stationary base model will take care of quite a number of tasks, and can also be mounted in a router table should you choose to invest in (or even build one) one down the line. Choose a router model that is at least 2-HP and has electronic variable speed controls (as larger cutting bits should use slower speeds), a soft start mechanism and is easy to make bit changes (preferably with the ability to use both 1/2-inch and 1/4-inch shank router bits).
Over the years we've been asked numerous times if we carry children's tool sets. Unfortunately most of the tool sets commercially marketed for children are more like toys than real tools, and they either tend to break, or are unusable to begin with. Like learning to play music on a cheap instrument, working wood with poorly constructed tools will soon frustrate even the most ambitious student.
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]
I tried to write a book that contains all the essential information for the novice woodworker as well as some more advanced tips and tricks to jumpstart your existing woodworking skills. You won’t find any useless theories or unnecessary technical jargon to bog you down. What you will find is practical, hands-on information and advice that will save you hours of frustration (pretty good deal, huh?).

This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
now I finally know what to recommend my friends when I try to convince them to give handtools a try (I currently am doing an apprenticeship in cabinetmaking (unfortunately mostly particle board) and said friends they do the same and often have no clue what can be achieved with handtools alone) because up until now, I never knew what to recommend for sharpening as my setup is great but very expensive. And I guess if I recommend to get two stones instead of a combination stone, one can keep one side flat for flattening the backs of new chisels, and add a strop with some polishing compound I really can’t think of anything else one would need for a long time!
Just bought this book.I want to learn to build things in wood.I have some tools but those joints are giving me problems. I have design books but how do I make a mortise joint or when to use tendon joint or a rabbit or use dowels? Who knew.I got some basic things but now I can actually finish my projects oh Joy.I can't wait till it arrives .Thank you Amazon and Hippo_Books for this book. When I get better at building stuff I will be back to update my review.Oh to all of you reviewers ....I bought this book cause of you.So thank you.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close
After the wood is cut it needs to dry before it can be used, and drying the wood causes shrinkage in the board. So it’s important that the board be allowed to dry evenly or it twists, bows, or warps. If you buy wood from a lumberyard, it’s already been dried, but you want to acclimate it to your shop before you work with it. This way the wood will make any changes it needs to make with the different humidity level in your shop, and you don’t get any nasty surprises like a table leg that twists after you’ve glued your project together.

The key to making furniture is having a plan. (Or is that the key to life? I always forget.) The good news for beginning woodworkers is that you don’t need to develop the plan; you need only to follow it. Project plans are abundant and easily found (check out Chapter 21 for some project-plan resources). After you get familiar with the way plans are written, you can build just about anything (depending on your skills, of course).
If I were to give someone new one piece of advice, it would be to buy their chisels new, not used. I have wasted more time and more money trying to save butchered chisels than I want to admit. There’s a good chance that the used chisel will be bellied in the back or pitted at the edge and it will take more than beginner skills to fix it. You may make things worse rather than better. Sure, learn to do this _some_ day, but maybe not as a beginner first thing. I’ve had similar problems with used planes, but it isn’t nearly as bad a problem for a joinery plane. If there are pits that lead to scratches, it may not matter for anything other than a final smoother. Also, a tiny back bevel may save the day on a plane, but you likely don’t want that on a chisel. So, I’m less fussed about planes and, if it all goes south, you can buy a new blade for smoothing work and use the old for rough work (all in the same plane). You can’t buy a new blade for a chisel. Well, you can, but it’s called buying a new chisel. I use 3/8″ a lot. 1/4, 3/8 to handle all the mortises and dovetails and either 3/4 or 1″ for paring shoulders and for fat parts of some dovetails. I probably learn towards the 1″ because there are times you want to reference off the blade to keep moving in a line, like for a housing. I think Lee Valley’s version of the Narex are excellent and mine came with flat backs that could go straight to polishing.

Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
Over the years we've been asked numerous times if we carry children's tool sets. Unfortunately most of the tool sets commercially marketed for children are more like toys than real tools, and they either tend to break, or are unusable to begin with. Like learning to play music on a cheap instrument, working wood with poorly constructed tools will soon frustrate even the most ambitious student.
Part I is your introduction to woodworking, wood, and woodworking shops. Chapter 1 gives you an overview of the woodworking process and gets absolute beginners up to speed on this fascinating hobby. Chapter 2 helps you to understand the unique qualities of wood. You discover the various types of wood used in furniture and how to find and buy the right boards for your projects. Because woodworking is an inherently dangerous activity, Chapter 3 shows you how to create a safe working environment and gives you some guidelines for working as safely as possible.

I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
I tried to write a book that contains all the essential information for the novice woodworker as well as some more advanced tips and tricks to jumpstart your existing woodworking skills. You won’t find any useless theories or unnecessary technical jargon to bog you down. What you will find is practical, hands-on information and advice that will save you hours of frustration (pretty good deal, huh?).

I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.

I agree, that’s a nice and easy set up to start with. I’d say a block plane it’s handy for small areas, and touch ups. A no.5 is excellent but a bit heavy and tiring sometimes. I find that a nice rabbet block plane (shoulder + block) with two irons with different sharpening angles it’s essential to me. One fine flat rasp and a medium flat file would complete my set.
×