John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
This snowman kit post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. The snowflakes are falling softly on the ground. You grab your hat, coat and mittens and head outside to test the snow. … [Read more...]
Dividers (or compass) are used for taking and repeating a measurement over and over again on a work piece. Traditional woodworkers rarely take measurements with a tape measure when doing fine joinery work, but rather take a measurement with dividers then transfer that arbitrary (yet accurate) measurement to another work piece. This removes a degree of inaccuracy.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.
I tried to write a book that contains all the essential information for the novice woodworker as well as some more advanced tips and tricks to jumpstart your existing woodworking skills. You won’t find any useless theories or unnecessary technical jargon to bog you down. What you will find is practical, hands-on information and advice that will save you hours of frustration (pretty good deal, huh?).
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project. 

The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.

About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.

Definitely worth reading and extremely helpful for beginners and those wondering what it's all about. The problem comes with the large number of tools one needs before you can even start to contemplate whether this is a hobby for you. A better approach might be to pick one tool and then show what a true beginner can do with that in order to create some enthusiasm for woodworking.

The very affordable coping saw (often around $20) is regularly used for rough cutting shapes in the board, but especially for removing waste from dovetail joints (one of the most common wood joints). An affordable coping saw will work just fine as long as you have plenty of replacement blades on hand (also very affordable). Read my hand saw buying guide for more detail on brands & features to look for when purchasing a coping saw.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.

Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
Whether he’s teaching at North Bennet Street School or working in his home shop, furniture maker Dan Faia wants certain essential hand tools close by. As it happens, the compact tool rack also featured in this issue holds them all. Your list may vary, but this comprehensive list of hand tools for layout, surface prep, shaping, and joinery is a good starting point for any aspiring hand-tool woodworker.
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
The final step in any woodworking project is protecting the wood from moisture and damage. Chapter 18 includes lots of information about the most common types of topcoats. Because not all of them provide the same degree of beauty and protection, you get a chance to compare the pros and cons of each topcoat so that you can choose the best option for you and your project.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.

When I started out woodworking I’d watch television shows and read magazines pushing all kinds of fancy new tools and think “If only I had a shop full of those tools I could build anything.” I spent a long time saving my pennies, reading the reviews and trying out the latest tools. The models seemed to change with the seasons. New project? Time for a new bit, jig or gizmo. Realizing that earlier craftsmen didn’t have access to all of these modern wonders yet they produced far more intricate work, I began to approach woodworking by more ancient means.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
As someone who finds hand planing a challenge the minimalist approach seems like the best way to truly learn a tools quirks and develop the skill required. So the Veritas BU planes are going along with the Tormek required to sharpen those gargantuan irons and a diamond plate and oil stone are on the way to get my old Stanley no 5 humming. I never found a sharpening routine that didn’t look a ball ache to keep the BU planes working well and being a stick thin wimp the weight of the buggers for anything more than controlled smoothing shavings knackered me out.
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ...  More + Product Details Close
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
Definitely worth reading and extremely helpful for beginners and those wondering what it's all about. The problem comes with the large number of tools one needs before you can even start to contemplate whether this is a hobby for you. A better approach might be to pick one tool and then show what a true beginner can do with that in order to create some enthusiasm for woodworking.
Dividers (or compass) are used for taking and repeating a measurement over and over again on a work piece. Traditional woodworkers rarely take measurements with a tape measure when doing fine joinery work, but rather take a measurement with dividers then transfer that arbitrary (yet accurate) measurement to another work piece. This removes a degree of inaccuracy.
When I started out woodworking I’d watch television shows and read magazines pushing all kinds of fancy new tools and think “If only I had a shop full of those tools I could build anything.” I spent a long time saving my pennies, reading the reviews and trying out the latest tools. The models seemed to change with the seasons. New project? Time for a new bit, jig or gizmo. Realizing that earlier craftsmen didn’t have access to all of these modern wonders yet they produced far more intricate work, I began to approach woodworking by more ancient means.

Tools for children must work right out of the box without modification. Only a minimal amount of skill should be necessary to put the tools into service, and they need to fit small hands. The tools contained in the Highland Woodworking Kids' Tool Kit meet these standards, and are suitable for kids 7 years old and up with adult supervision. As for materials, stick with softer woods like white pine and basswood. These woods are inexpensive, easy to work and readily available at any home center.
I have so many free woodworking plans on the site, that it is so hard for a beginner to choose something both simple to build and fulfilling. That is why, I decided to make a short list with my top 20 favorite projects that can be built by any person with basic woodworking skills and limited tools. Even if it might look intimidating at first, my detailed plans and step by step instructions make it really easy for anyone to get the job done.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.

excellent post! noone can beat good advice from someone who makes a living at this. it’s struggle to commit to minimal tools but i can attest to getting too many too soon and not mastering them all. it can even slow down a project trying to fiddle with a new tool and create some waste. i’ve taken to the idea to make 6 projects with the same problem i like to solve with a specialty tool. then ask do i really need it.. for instance i want to incorporate more sliding dovetails. as per you sound advice you don’t need anything more than what you listed but i keep eyeing a dovetail planes both male and female. i just saying resist and build! learn efficiency with what i have and decide if its a roadblock to success or profitability


Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
As someone who finds hand planing a challenge the minimalist approach seems like the best way to truly learn a tools quirks and develop the skill required. So the Veritas BU planes are going along with the Tormek required to sharpen those gargantuan irons and a diamond plate and oil stone are on the way to get my old Stanley no 5 humming. I never found a sharpening routine that didn’t look a ball ache to keep the BU planes working well and being a stick thin wimp the weight of the buggers for anything more than controlled smoothing shavings knackered me out.
×