about three years ago I thought to make even only a cutting board I would need a complete set of machines, stationary and handmachines, plus of course a few handtools for “hybrid woodworking”, then I discovered Peter Sellers and most importantly Chris and The Anarchist’s Tool Chest, that was a revelation! So I find it absolutely awesome that you show us how to start with even less tools (especially the advice for saws is great, much cheaper to only get rip)!

Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.

This snowman kit post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. The snowflakes are falling softly on the ground. You grab your hat, coat and mittens and head outside to test the snow. … [Read more...]
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
My Stanley 51/2 was in a bit of a state when I got it and refurbing it took a bit of time and cash. Now it works a treat and looks like new. I’m nearly through the bench build and have spend hours using it – it really is a workhorse piece of kit. I did some final cleaning up of some oak legs the other day and I can’t really see how a smaller plain would do a better job.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
After you have chosen the perfect table saw for your wood shop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
John P, 3/18/2014 I lost most of my tools in the divorce. I have gotten a tool here and there over the past few years. I needed a plane and went to Google to see what was available. I found this starter set and placed my order. The planes exceeded my expectation and I have used them successfully on several projects. I recommend this starter set to all without reservation!
The key to making furniture is having a plan. (Or is that the key to life? I always forget.) The good news for beginning woodworkers is that you don’t need to develop the plan; you need only to follow it. Project plans are abundant and easily found (check out Chapter 21 for some project-plan resources). After you get familiar with the way plans are written, you can build just about anything (depending on your skills, of course).
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
I quickly found that power equipment was not broadening my capabilities as much as it was like an anchor tethering me to a limited band of work and taking up valuable shop space. I also didn’t like wearing the requisite dust mask, hearing protection and safety glasses all the time – it was like a mini sensory deprivation chamber. When I asked master cabinetmaker Dan Faia what he does for dust protection in his own shop, his succinct reply was “I never coughed up a curl.” That pithy remark reflected the very different view traditional woodworkers have – without all the big machines, the dust and noise, you can focus on the work, invest in a smaller set of high quality tools that should last a lifetime and enjoy the process as much as the result.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
excellent post! noone can beat good advice from someone who makes a living at this. it’s struggle to commit to minimal tools but i can attest to getting too many too soon and not mastering them all. it can even slow down a project trying to fiddle with a new tool and create some waste. i’ve taken to the idea to make 6 projects with the same problem i like to solve with a specialty tool. then ask do i really need it.. for instance i want to incorporate more sliding dovetails. as per you sound advice you don’t need anything more than what you listed but i keep eyeing a dovetail planes both male and female. i just saying resist and build! learn efficiency with what i have and decide if its a roadblock to success or profitability
Many species of wood fall into two general categories: hardwoods and softwoods. Knowing which type of wood is which and being able to choose the right wood for your goals can help reduce the negative impact of the inherent instability that is a part of solid wood. As you discover the variability of wood, you’ll undoubtedly come to appreciate that some wood products allow you the same level of beauty without having to worry about the wood changing shape on you. These include veneers and manufactured wood products such as plywood and Medium Density Fiberboard (MDF). All this talk of wood is covered in more detail in Chapter 2.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.

ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 917 S. Lusk Street, Suite 200, Boise Idaho, 83706, USA and used by permission. ClickBank's role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
×