Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
Thank you for this post. I am about three years into wood working with handtools. I didn’t want to be a handtool collector. I wanted a good set of tools I could use. Since funds were tight and I wasn’t sure if I would keep doing this, I wanted to build my tools slowly. What you outlined is more or less what I ended up getting and it has indeed served me well. One can easily do a lot with all of these tools. At some point about two years into the hobby, I had a much better feel for what I wanted to make and what I may or may not need beyond this.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
*Northern Ireland, Scottish Highlands and Islands usually receive a 2-3 working day service for First Class. For Tracked Courier, it’s a 2 working day service and you need to order by 15:00. Unfortunately, we don't currently offer Express Delivery outside the UK, Gibraltar, Guernsey or Jersey. All deliveries are subject to cut-off times and public holidays.
A staple of every For Dummies book, Part IV presents the Part of Tens. Chapter 19 includes ten good habits to get into to make your woodworking experience safer. Chapter 20 offers ten woodworking pitfalls that almost everyone encounters at one time or another. (Oh, and ways to avoid or fix them, too.) Chapter 21 gives you some woodworking resources so that you can keep expanding your woodworking knowledge.
Other than the panel saw, all my kit fits into a 50x33x17cm wooden wine box. After years of relying on power tools for everything, I’ve found this minimalist approach very refreshing. Asking myself ‘will it fit in the box?’ helps me to curb ‘add to basket’ tendencies. My only additions to your list are a Stanley No. 18 block plane, a Lie Nielsen dowel plate and a small engineers set square, all non-essential but they do get used.
The very affordable coping saw (often around $20) is regularly used for rough cutting shapes in the board, but especially for removing waste from dovetail joints (one of the most common wood joints). An affordable coping saw will work just fine as long as you have plenty of replacement blades on hand (also very affordable). Read my hand saw buying guide for more detail on brands & features to look for when purchasing a coping saw.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Over the years we've been asked numerous times if we carry children's tool sets. Unfortunately most of the tool sets commercially marketed for children are more like toys than real tools, and they either tend to break, or are unusable to begin with. Like learning to play music on a cheap instrument, working wood with poorly constructed tools will soon frustrate even the most ambitious student.
Second, I assumed that you want to do things the fast and easy way and not necessarily the old-fashioned way. As you’ll likely find out by talking to other woodworkers, you can find almost as many ways to perform a task as you can find woodworkers. Everyone has his own unique way to do things and mine involves taking advantage of modern tools and shortcuts, rather than using old-fashioned, time-consuming, and often frustrating approaches that can be done better with modern tools and approaches (do you sense a little bias here?). For example, if you want to find out how to craft dovetails by hand with a chisel and backsaw, buy another book. But if you want to make joints that are just as strong and beautiful in a fraction of the time with a router and a jig, then this book is for you. (Don’t worry, in this book, you will still get to see many of the traditional ways things are done, if for no other reason than to help you decide for yourself how you want to approach a task.)
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
John, 9/18/2012 Arrived quickly and in a real beautiful box. I sharpened and honed the planes and used them to smooth some old cedar boards. They worked flawlessly even for this beginning woodworker. A real joy using these types of tools instead of power sanding tools and the like. I have never used a Spokeshave before but can already see that it will be very useful as I progress in my journey from welder to woodworking.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.