Sometimes Grandparents can be hard to buy gifts for, they seem to have everything already. But hey you can't go wrong with darling gifts of grand kids, right!?! In this post I'm going to share a couple of ideas for personalized photo gifts. To make the photo gifts, I will be using Photoshop Elements 2018. I have been using Photoshop Elements ever since I graduated from trying … [Read more...]
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
This is a super cheap option for a pretty diverse tool. Like, how wrong can you go for $34, right? This tool rocks for doing cuts on larger pieces of wood that need to be more detailed than your circular saw will allow. For more detailed work I would totally go for a scroll saw, or even a band saw. But if you are building your tool box, this is a much more approachable item, both price wise and in terms of ability to be used in diverse ways. And, hey, woodworking isn’t exactly inexpensive, right?
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Youve seen a few shows on TV, and working with wood looks like it could be quite entertaining and rewarding. After all, you get to create something that you can proudly display to your friends and family. But where and how do you begin to move from expressed interest to hands-on experience? Woodworking For Dummies shows you how your raw building materials stack up, with everything you wood need to know about hardwood, softwood, plywood, veneer wood, plain-sawn wood, rift-cut wood, quarter-sawn wood, solid wood, man-made wood, and more. This down-to-earth guide gives you the goods on how boards are made from trees and the characteristics of hardwood and softwood species, plus all the buzz on Gearing up with the right tools Putting safety first in your workshop Using adhesives and glue Working with wood joints Smoothing it out by sanding and filling Adding color with stains and paints Protecting your work with topcoats Whether you want to put together a simple plywood bookcase or an incredible solid oak dining table, Woodworking For Dummies can help you get organized as you craft your plans for a piece thatll reflect your personal touch. Youll discover how to Measure and mark your wood Distinguish among saw designs Choose and use sharpening tools Hone in on hot melt glue Speed things up with modern frame joints Get down to the nitty-gritty on nails Apply water-based polyurethanes This handy reference packs in essential information for the novice woodworker and some advanced tips and tricks to jumpstart any woodworkers existing skills. Includes detailed illustrations and how-to photos.
Finally, a workbench. Like most people, I started with a DIY workbench that totally did the trick for the first couple of years. I recently upgraded to a Kreg workbench, and it is awesome. It moves around so smoothly, it’s incredibly durable and strong, and it combines form and function in ways that make my heart sing. If you, like me, are working out of a garage or small shop, consider the value of something that moves about extremely well, and that is adaptable to your needs. They have several sizes to choose from, so I’ll link to the main product page.
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
John P, 3/18/2014 I lost most of my tools in the divorce. I have gotten a tool here and there over the past few years. I needed a plane and went to Google to see what was available. I found this starter set and placed my order. The planes exceeded my expectation and I have used them successfully on several projects. I recommend this starter set to all without reservation!
Quarter-sawn: Quarter-sawn milling is the least efficient way to cut a log, but it produces some of the best boards. You can mill a quarter-sawn board in two ways: the preferred way (Figure 2-3 left) and the practical way (Figure 2-3 right). Unless you have a mill of your own or you own the log and have it milled to your specifications, you’re going to have to live with the practical method of quarter-sawing wood. Don’t worry, this is still a great way to mill a log and, because it’s more efficient than the preferred method, it doesn’t cost you an arm and a leg to buy (maybe just the arm).
Gord, 1/2/2013 Nice inexpensive starter set I purchased for my Little Brother. The planes were easy to disassemble for sharpening and the blades sharpened easily. The blades were ground a bit low in the center but was easily corrected with a course stone. There was a problem with the wooden box and after a few iffy phone calls a replacement box was received well before Christmas.
Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]
Two things which I took to instantly and now wouldn’t want to do without are an old-fashioned two foot, four fold ruler which gets used all the time (there’s nothing that comes close to it) and a 1 1/2″ butt chisel which gets used all the time for marking anything which needs to be chopped e.g. the side of a mortice. It also means fewer chops and therefore a bit more accuracy when cutting out a knife wall.
Basically, as you beginner you will need the following tools: a drill, an impact driver, a miter saw and a sander. With these tools you can cut, join and finish wood as a professional. If you want to save time and improve the quality of your work you can upgrade and buy yourself a pocket hole jig, a router, a thickness planer and a table saw. I have created a complete guide with tool recommendations and reviews HERE, so you make an informed decision.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Woodworking For Dummies shows you how your raw buildingmaterials stack up, with everything you wood need to knowabout hardwood, softwood, plywood, veneer wood, plain-sawn wood,rift-cut wood, quarter-sawn wood, solid wood, man-made wood, andmore. This down-to-earth guide gives you the goods on how boardsare made from trees and the characteristics of hardwood andsoftwood species, plus all the buzz on
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.