With all this tool talk, you’ll probably be tempted to buy every one that I describe in this book. Well, to keep you from going broke, I offer some advice on which tools to buy when, so that you can slowly and sanely build your workshop as you build your woodworking skills. See Chapter 4 for more on this topic. Chapter 8 helps you set up your shop so that you can get to all of your tools without hassle. You can also explore shop essentials, such as lighting and electrical requirements, to ensure that you can see what you’re doing and can run all the tools you want to use.
24″ for the chopping block. all of my lumber comes from last years spring clean up. currently have Cherry, White oak, Ash, Hard & Soft Maple as Well as Sasafrass on hand there is also Birch in the woods but none of them have needed to come down yet. I keep two single bevel axes one light one Heavy(2-1/2 lb) which I use depends on how my Elbow feels. A Froe is also required. I think going from tree to board is harder than from board to furniture but it depends how much wind is in the tree. I don’t think I would of ever been able to build the required skills if I had to pay for the lumber though I guess I paid in labor. Air dried stuff is some much better to work with its worth it.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Wood sold by the board foot may or may not be smooth on all sides and only one edge may be square. A board foot is a board that is 1 inch thick (called 4/4) by 12 inches wide by 1 foot long. To figure out how many board feet are in a piece of wood, multiply its length (measured in feet), width, and thickness (measured in inches) and divide this number by 12.
It’s okay to buy wood with knots, splits, cracks, and checks. These defects affect only a small area of the board (if they exist over the majority of the board, don’t buy it), so you can plan your cuts around them. Avoid boards with warps, twists, or bows. It takes a lot of time to flatten a board that has one of these defects. To test for these defects, place one end of the board on the floor and hold the other end to your eye. The board should be straight and true. If not, leave it there.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Always be on the lookout for usable wood. You might be able to salvage some. You can use a metal detector to find nails and screws. You don’t need a full fledged metal detector. I use a pinpointer made by Garrett. If your wood has some woodboring beetles you can still use it if not eaten too badly. A healthy dose of cyfluthrin will take care of them.
Part IV is filled with really cool projects. The purpose of this section is to give you some woodworking experience and to progressively build your skills. Chapter 12 leads you through the process of making a project so that you know what you’re getting into before you begin cutting wood. Chapter 13 gets you started woodworking with the easiest project to build — a bookcase. Not just one bookcase, but several, so you’re sure to find one that fits your design ideals. Chapter 14 builds on the skills you developed in Chapter 13 by helping you build tables. Like Chapter 13, you have several table designs to choose from (heck, build ’em all; you can never have too many tables!). Chapter 15 ups the ante by providing projects for making cabinets with either drawers or doors. Again, you get to choose among several really good designs (if I do say so myself).
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ... More + Product Details Close