Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
You need tools to work with wood. And most woodworkers think tools are great. I know I love buying and using tools. Heck, I’m the first to admit I have a problem. (Does anyone know of a 12-step program for tool addicts?) I buy tools like candy (well, more than I buy candy, actually). I have special tools for almost any imaginable task and I can’t ever seem to get enough. Such is the life of a woodworker.
John Oesleby, 11/7/2018 I lost my workshop and tools in the California wildfires, and thought this set would get me started again. It’s a good value, but does require some fine tuning. There are a lot of videos online. I found the following: The blades are lightweight, and need sharpening. The edge of one (the block plane) had been visibly overheated, and required some effort to get to undamaged steel. It doesn’t seem to hold an edge long. On the smoothing plane, the sole is concave, and will need some effort to flatten. The frog resisted adjustment because the adjustment screw was drilled a little to close to the sole. I got the frog into an acceptable position be removing the washers from the hold-down screws. The chip breaker needed some work to fit the blade properly. Overall, I feel the set was a decent value.
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.
After the wood is cut it needs to dry before it can be used, and drying the wood causes shrinkage in the board. So it’s important that the board be allowed to dry evenly or it twists, bows, or warps. If you buy wood from a lumberyard, it’s already been dried, but you want to acclimate it to your shop before you work with it. This way the wood will make any changes it needs to make with the different humidity level in your shop, and you don’t get any nasty surprises like a table leg that twists after you’ve glued your project together.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ... More + Product Details Close
On chisels, once a new comer learns to sharpen, Aldi sells a 4 chisel pack for about $20 US. They are blunt and the backs need to be flattened but once correctly sharpened, they hold their edge very well. These are my go to chisels for most work and they’re as sharp as a scalpel. My good chisels haven’t seen the light of day in over a year as the Aldi chisels work beautifully.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
Sometimes Grandparents can be hard to buy gifts for, they seem to have everything already. But hey you can't go wrong with darling gifts of grand kids, right!?! In this post I'm going to share a couple of ideas for personalized photo gifts. To make the photo gifts, I will be using Photoshop Elements 2018. I have been using Photoshop Elements ever since I graduated from trying … [Read more...]
Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ... More + Product Details Close